Dell Inspiron 5559移除硬盘后Windows 10启动报MEMORY MANAGEMENT错误

Hey there, let's tackle this frustrating MEMORY MANAGEMENT blue screen issue you're dealing with. Since Linux Mint boots up perfectly fine, we can safely rule out hardware problems like faulty RAM or a failing drive—this is almost certainly a Windows-specific glitch triggered by disconnecting and reconnecting your hard drive. Here are targeted fixes to try:

1. Repair Windows Boot & System Files #

First, let's fix any corrupted boot records or system files that might have gotten messed up during the drive swap:

• Grab a Windows 10 installation USB (you can create one on another PC if you don't have it) and boot from it.
• Select "Repair your computer" → "Troubleshoot" → "Command Prompt".
• Run these commands one by one (press Enter after each):
  • bootrec /fixmbr (fixes the master boot record)
  • bootrec /fixboot (repairs the boot sector)
  • bootrec /rebuildbcd (rebuilds the boot configuration data store)
  • chkdsk C: /f /r (replace C: with your Windows system drive letter if it's different; this checks and fixes drive errors)
  • sfc /scannow (scans and repairs corrupted system files)

2. Reset Virtual Memory Settings #

MEMORY MANAGEMENT errors often tie to virtual memory issues, and the page file might have gotten corrupted when you disconnected the drive:

• If you can boot into Windows Safe Mode (restart your PC and hold Shift when clicking "Restart", then select "Troubleshoot" → "Advanced options" → "Startup Settings" → "Enable Safe Mode"):
  • Right-click "This PC" → "Properties" → "Advanced system settings".
  • Go to the "Advanced" tab → under "Performance", click "Settings".
  • Switch to the "Advanced" tab again → click "Change" under Virtual Memory.
  • Uncheck "Automatically manage paging file size for all drives".
  • Select your Windows system drive, choose "No paging file", click "Set", then restart your PC.
  • After restarting, go back through the same steps and re-enable automatic paging file management (or set a custom size if you prefer).

3. Tweak BIOS/UEFI Settings #

Sometimes drive disconnects can cause BIOS settings to glitch—let's double-check these:

• Restart your Dell Inspiron 5559 and press F2 repeatedly to enter BIOS.
• Verify these settings:
  • SATA Mode: Ensure it's set to AHCI (this is the standard for dual-boot setups; switching to IDE can cause compatibility issues).
  • Memory Settings: If you had XMP enabled for overclocking RAM, try disabling it temporarily—sometimes drive swaps can trigger RAM compatibility hiccups.
  • Boot Order: Make sure your Windows boot partition is listed in the boot order, and use the "Detect Drives" option if available to refresh drive recognition.

4. Uninstall Problematic Storage Drivers #

If your storage drivers got corrupted during the drive swap, this could cause memory-related crashes:

• Boot into Safe Mode (steps above).
• Open Device Manager (right-click Start → Device Manager).
• Expand "Storage controllers", right-click each entry (like Intel SATA AHCI Controller) and select "Uninstall device". Check the box "Delete the driver software for this device" if available.
• Restart your PC—Windows will automatically reinstall the correct drivers.

5. System Restore or Windows Reset (Last Resorts) #

If all else fails:

• System Restore: Boot into Safe Mode, search for "Create a restore point", go to the "System Protection" tab, click "System Restore", and choose a restore point from before you disconnected the drive.
• Reset Windows: If you don't have a restore point, use Windows' reset feature (boot from installation USB → "Repair your computer" → "Troubleshoot" → "Reset this PC") and select "Keep my files" to retain your personal data while reinstalling system files.

Since Linux runs without issues, hardware failure is highly unlikely—focus on these Windows-specific fixes and you should get back up and running.

内容的提问来源于stack exchange，提问作者admin-jonah