通过Web控制无法切换MotionEye运动检测状态求助

我使用树莓派4搭载64位Raspberry Pi OS Lite（Debian Bullseye移植版），并按照官方指南安装了Motion Eye。由于系统是64位，安装时改用了对应arm64架构的motion 4.5.1软件包。目前C922 Pro Stream网络摄像头连接后整体运行正常。

通过命令行切换摄像头1的运动检测状态。

参考motion官方Web控制文档，尝试用HTTP请求控制运动检测状态：

• 查看检测状态的命令：

sudo wget -q -O - "http://raspberrypi:7999/1/detection/status" | grep Camera | sed -e "s/<[^>]*>//g" -e "s/.*Camera/Camera/"

执行后输出：

Camera 1 Detection status PAUSE

在Web界面开启运动检测并点击应用后，重新执行上述状态查询命令，输出：

Camera 1 Detection status ACTIVE

• 尝试从暂停状态开启检测的命令：

sudo wget -q -O - "http://raspberrypi:7999/1/detection/start" | grep Camera | sed -e "s/<[^>]*>//g" -e "s/.*Camera/Camera/"

响应结果为：

Camera 1 Detection resumed

再次执行状态查询命令，输出显示：

Camera 1 Detection status ACTIVE

执行开启检测的命令后，返回Web界面刷新，运动检测切换开关仍显示为关闭状态，且实际无法检测运动。尝试重启摄像头1和树莓派后，开关依然显示关闭。推测可能存在权限问题，但命令执行返回了成功响应，却未实现预期效果。

/etc/motioneye/motion.conf 当前内容 #

# @enabled on
# credentials have been removed 

webcontrol_interface 2
webcontrol_port 7999
setup_mode off
webcontrol_parms 2
webcontrol_localhost off

camera camera-1.conf

/etc/motioneye/motioneye.conf 当前内容 #

# path to the configuration directory (must be writable by motionEye)
conf_path /etc/motioneye

# path to the directory where pid files go (must be writable by motionEye)
run_path /var/run

# path to the directory where log files go (must be writable by motionEye)
log_path /var/log

# default output path for media files (must be writable by motionEye)
media_path /var/lib/motioneye

# the log level (use quiet, error, warning, info or debug)
log_level debug

# the IP address to listen on
# (0.0.0.0 for all interfaces, 127.0.0.1 for localhost)
listen 0.0.0.0

# the TCP port to listen on
port 8765

# path to the motion binary to use (automatically detected if commented)
#motion_binary /usr/bin/motion

# whether motion HTTP control interface listens on
# localhost or on all interfaces
motion_control_localhost true

# the TCP port that motion HTTP control interface listens on
motion_control_port 7999

# interval in seconds at which motionEye checks if motion is running
motion_check_interval 10

# whether to restart the motion daemon when an error occurs while communicating with it
motion_restart_on_errors false

# interval in seconds at which motionEye checks the SMB mounts
mount_check_interval 300

# interval in seconds at which the janitor is called
# to remove old pictures and movies
cleanup_interval 43200

# timeout in seconds to wait for response from a remote motionEye server
remote_request_timeout 10

# timeout in seconds to wait for mjpg data from the motion daemon
mjpg_client_timeout 10

# timeout in seconds after which an idle mjpg client is removed
# (set to 0 to disable)
mjpg_client_idle_timeout 10

# enable SMB shares (requires motionEye to run as root)
smb_shares false

# the directory where the SMB mount points will be created
smb_mount_root /media

# path to the wpa_supplicant.conf file
# (enable this to configure wifi settings from the UI)
#wpa_supplicant_conf /etc/wpa_supplicant.conf

# path to the localtime file
# (enable this to configure the system time zone from the UI)
#local_time_file /etc/localtime

# enables shutdown and rebooting after changing system settings
# (such as wifi settings or time zone)
enable_reboot false

# timeout in seconds to use when talking to the SMTP server
smtp_timeout 60

# timeout in seconds to wait for media files list
list_media_timeout 120

# timeout in seconds to wait for media files list, when sending emails
list_media_timeout_email 10

# timeout in seconds to wait for zip file creation
zip_timeout 500

# timeout in seconds to wait for timelapse creation
timelapse_timeout 500

# enable adding and removing cameras from UI
add_remove_cameras true

# enables HTTP basic authentication scheme (in addition to, not instead of the signature mechanism)
http_basic_auth false

# overrides the hostname (useful if motionEye runs behind a reverse proxy)
# server_name motionEye

内容的提问来源于stack exchange，提问作者Mark Lewis