LilyGo T5 4.7" ESP32 S3编译报错：int*转int32_t*无效

我购买了一款搭载ESP32 S3的LilyGo T5 4.7"新一代墨水屏，已安装必要的库和板管理器，并按照步骤配置Arduino IDE，但无论如何操作，编译始终报错：

compilation error: invalid conversion from 'int*' to 'int32_t*' {aka 'long int*'} [-fpermissive]

在另一台电脑上按相同步骤操作可正常编译，附上我的代码如下：

#ifndef BOARD_HAS_PSRAM
#error "Please enable PSRAM !!!"
#endif

#include <Arduino.h>
#include "epd_driver.h"
#include "font/firasans.h"
#include "esp_adc_cal.h"
#include <FS.h>
#include <SPI.h>
#include <SD.h>
#include "image/logo.h"
#include "pins.h"

#if defined(T5_47_PLUS)
#include "pcf8563.h"
#include <Wire.h>
#endif


#if defined(T5_47_PLUS)
PCF8563_Class rtc;
#endif

int vref = 1100;

void setup()
{
    Serial.begin(115200);
    delay(1000);

    char buf[128];
    /**
    * SD Card test
    * Only as a test SdCard hardware, use example reference
    */
    SPI.begin(SD_SCLK, SD_MISO, SD_MOSI, SD_CS);
    bool rlst = SD.begin(SD_CS, SPI);
    if (!rlst) {
        Serial.println("SD init failed");
        snprintf(buf, 128, "➸ No detected SdCard");
    } else {
        Serial.println("SD init success");
        snprintf(buf, 128,
            "➸ Detected SdCard insert:%.2f GB",
            SD.cardSize() / 1024.0 / 1024.0 / 1024.0
        );
    }

    // Correct the ADC reference voltage
    esp_adc_cal_characteristics_t adc_chars;
#if defined(T5_47)
    esp_adc_cal_value_t val_type = esp_adc_cal_characterize(
        ADC_UNIT_1,
        ADC_ATTEN_DB_11,
        ADC_WIDTH_BIT_12,
        1100,
        &adc_chars
    );
#else
    esp_adc_cal_value_t val_type = esp_adc_cal_characterize(
        ADC_UNIT_2,
        ADC_ATTEN_DB_11,
        ADC_WIDTH_BIT_12,
        1100,
        &adc_chars
    );
#endif
    if (val_type == ESP_ADC_CAL_VAL_EFUSE_VREF) {
        Serial.printf("eFuse Vref: %umV\r\n", adc_chars.vref);
        vref = adc_chars.vref;
    }

#if defined(T5_47_PLUS)
    Wire.begin(TOUCH_SDA, TOUCH_SCL);
    rtc.begin();
    rtc.setDateTime(2022, 6, 30, 0, 0, 0);
#endif

    epd_init();

    Rect_t area = {
        .x = 230,
        .y = 20,
        .width = logo_width,
        .height = logo_height,
    };

    epd_poweron();
    epd_clear();
    epd_draw_image(area, (uint8_t *)logo_data, BLACK_ON_WHITE);
    epd_poweroff();


    int cursor_x = 200;
    int cursor_y = 250;

    const char *string1 = "➸ 16 color grayscale  😀 \n";
    const char *string2 = "➸ Use with 4.7\" EPDs 😍 \n";
    const char *string3 = "➸ High-quality font rendering ✎🙋";
    const char *string4 = "➸ ~630ms for full frame draw 🚀\n";

    epd_poweron();

    writeln((GFXfont *)&FiraSans, buf, &cursor_x, &cursor_y, NULL);
    delay(500);
    cursor_x = 200;
    cursor_y += 50;
    writeln((GFXfont *)&FiraSans, string1, &cursor_x, &cursor_y, NULL);
    delay(500);
    cursor_x = 200;
    cursor_y += 50;
    writeln((GFXfont *)&FiraSans, string2, &cursor_x, &cursor_y, NULL);
    delay(500);
    cursor_x = 200;
    cursor_y += 50;
    writeln((GFXfont *)&FiraSans, string3, &cursor_x, &cursor_y, NULL);
    delay(500);
    cursor_x = 200;
    cursor_y += 50;
    writeln((GFXfont *)&FiraSans, string4, &cursor_x, &cursor_y, NULL);
    delay(500);

    epd_poweroff();
}

void loop()
{
    // When reading the battery voltage, POWER_EN must be turned on
    epd_poweron();
    delay(10); // Make adc measurement more accurate
    uint16_t v = analogRead(BATT_PIN);
    float battery_voltage = ((float)v / 4095.0) * 2.0 * 3.3 * (vref / 1000.0);
    String voltage = "➸ Voltage: " + String(battery_voltage) + "V";
#if defined(T5_47_PLUS)
    voltage = voltage + String(" (") + rtc.formatDateTime(PCF_TIMEFORMAT_YYYY_MM_DD_H_M_S) + String(")");
#endif
    Serial.println(voltage);

    Rect_t area = {
        .x = 200,
        .y = 460,
#if defined(T5_47_PLUS)
        .width = 700,
#else
        .width = 320,
#endif
        .height = 50,
    };

    int cursor_x = 200;
    int cursor_y = 500;
    epd_clear_area(area);
    writeln((GFXfont *)&FiraSans, (char *)voltage.c_str(), &cursor_x, &cursor_y, NULL);

    // Turn off the power of the entire POWER_EN control and also turn off the blue LED light
    epd_poweroff_all();

    delay(5000);
}

请问有人能帮我解决这个问题吗？谢谢大家！

内容的提问来源于stack exchange，提问作者Jonathan Klein